Separators are sediment, oil and grease separators and serve to purify oily atmospheric, process, and technological waters. They are installed in the ground, in a dug pit, 20 cm deeper than the height of the separator and placed on a previously prepared concrete surface of 20 cm thick. After laying, PVC pipes are connected to the entrance and exit and are filled with water and check the permeability of the joints. The terrain around this prepared separator is then edited, ie, Adapts to the environment and provides access. If necessary, the separator is emptied of accumulated oil and grease, and it is necessary to take care of environmental protection

Technical characteristics:
* * Technical characteristics depend on the capacity of the separator.

Hydraulic press BSPV 5035051 DC12 serves for pressing secondary raw materials, PET and aluminum packaging and paper.
It is suitable for field work, is placed on a truck and is powered by DC (12V DC) via the battery. It is characterized by simple handling and automatic operation, small work space, low power consumption. Technical characteristics:
Total mass of the press:
400kg
Pressure dimensions:
A = 1890 mm
B = 700 mm
C = 550 mm
D = 1065 mm
E = 500 m

Internal dimensions of the chamber for pressing:
Height h = 770 mm
Length a = 500 mm
Width b = 350 mm
Bale length:
Height x length x width = 500 x 350 x 500 mm
Noise level:
max. 72 dB

Minimum dimensions for the accommodation of the press:
Working height 2000 mm
Working width with open door 1000 mm
Working space with open door 1200 m

Hydraulic characteristics:
Flow Q = 3.74 l / min
Working pressure p = 200 bar
Safety pressure p = 220 bar
Regenerative pressure p = 100 bar
Pressure force F = 50 kN (5 t)

Specific pressure in mass pa = 2,86 kN / cm2
Working cycle t = 42 s
Cylinder diameter D / d = 76/63 mm
Cylinder stroke H = 600 mm
Oil volume V = 15 l
Recommended hydraulic oil HD 32

Electrical characteristics:
Working voltage DC 12V
Control voltage 12V DC
Power of electric motor P = 1,5 kW,
The speed of the electric motor n = 1500 rpm

PThey are made of sheet metal and metal profiles in the volume of 1 m3, 2 m3 and 4 m3. They are used for storing and transporting bulk and piece materials. The special convenience for these vessels is that they are designed for quick and easy transport using forklifts. They are cheap for exploitation and they last long. Technical characteristics:

Construction GK-150, thanks to its strong construction, is primarily intended for the transportation of heavy construction material, concrete and similar cargo. The trough is made of 1mm thick sheet, while the supporting frame is made of L profile 3mm thick.
The wheel has a bearing with bearings and a pump that is pumped, Ø400 mm.
The weight of the carts is about 20 kg.

K-500 Park mowers are intended for mowing of grassy surfaces around houses and cottages, as well as city greenery and grassy sports grounds.
Because of its extremely light construction, the mower has special maneuvering skills, which are necessary for cutting grass in parks and areas planted with trees and decorative plants.

Technical characteristics

This machine is used for fast and clean cutting of grass in strips. After finishing the cut, the grass bar is simply wrapped up like a carpet, carried to the desired surface and spread to the already prepared terrain. In this way, the greening and repair of lawns in parks, sports grounds, stadiums, golf courses and other grasslands can be done in a short time.
The grass strips are uniform thickness and width, and the machine is easy and easy to serve.
The capacity of the cutter is about 500 m2 / h, the working width is 300 mm and the cut depth is adjusted to 60 mm. Four-stroke gasoline engine with a power of 4.41 kW is in charge, and the total weight of the machine is 128 kg.

It is intended for storing up to 3 bottles of gas under pressure. Materials and construction of cabinets prevent the occurrence of spillage when manipulating bottles. In the upper part of the cabinet there are ventilation openings, the stored bottles are provided from rolling, and the door of the storage cabinet is locked. The dimensions of the cabinet are:
H x B x D = 2350 x 1000 x 400 (mm).
The cabinet is mounted on the wall of the storage facility. At the request of the customer, it can be adapted for storage and a large number of bottles with pressure gas and equipped with additional equipment for special storage conditions. The color of the cabinet is gray or at the customer's request.

This device is used to discharge liquids from cars before their recycling and is a compulsory part of the equipment that must be dealt with by the companies involved. The principle of operation of this machine is to create a suppression in the system, which leads to the displacement of liquids into special vessels. Blok Signal is the first and only one in Serbia to do the project of this device.